Conductors

Bare overhead aluminium conductors for transmission and distribution, up to 127 strands. JSK is an approved vendor to Indian utilities and electricity boards, including PGCIL, and to EPC contractors in India and abroad.

Aluminium-clad invarThermal-resistant alloy

High Temperature Low Sag conductors

HTLS conductors run hotter than conventional conductors without sagging further, so an existing line can carry much more current. They are the practical way to uprate congested corridors, evacuate renewable power and modernise the grid without new right-of-way. Our strategic focus is to grow our share of high-performance and HTLS conductors to meet the rising demand on India's transmission and distribution network.

HC Alloy schematic cross-section
HC Alloy
Aluminium alloy

High-Conductivity Alloy Conductors

Advanced-generation overhead conductors designed to deliver superior electrical performance, lower transmission losses and excellent corrosion resistance. Widely used in renewable energy projects, transmission networks and utility infrastructure, they balance conductivity, mechanical strength and long-term reliability.

The aluminium alloys used are typically Al-Mg-Si alloys from the 6000 series. They offer improved efficiency over conventional conductors while keeping excellent sag-tension characteristics and durability.

Key advantages

  • Higher electrical conductivity for more efficient power transmission
  • Lower line losses and reduced operating costs
  • Excellent corrosion resistance in diverse environments
  • Superior sag-tension performance
  • Lightweight construction with a high strength-to-weight ratio
  • Enhanced reliability for renewable energy and utility projects
  • Long service life with minimal maintenance
  • Environmentally sustainable and recyclable

Applications

  • Renewable energy evacuation networks
  • Overhead transmission lines
  • Sub-transmission and distribution systems
  • Utility grid modernisation projects
  • Industrial power infrastructure
  • Long-span transmission
  • Coastal and corrosive environments
  • High-efficiency transmission networks

Available variants

  • AL-5
  • AL-6
  • AL-7
  • AL-57
  • AL-59
  • AL-60
  • AAAC 1120

Customised conductor configurations and specifications are available based on project requirements.

Construction and material

Specially engineered aluminium alloy wires, concentrically stranded to combine conductivity, strength, low weight and corrosion resistance. The alloy composition gives lower electrical resistance than conventional conductors, with excellent current-carrying capability and the mechanical characteristics overhead lines need.

Standards and quality

Manufactured in accordance with internationally recognised standards and utility specifications. Each conductor is manufactured to stringent quality standards, with rigorous testing at every stage, including type testing and validation.

AL59 conductor

An all-aluminium-alloy conductor whose mechanical and electrical properties are equivalent to ACSR and AAAC respectively. Best suited to enhancing the capacity of existing lines where additional power corridors are not feasible, and suitable for new lines.

  • Up to 30% lower I²R losses for the same conductor size
  • Runs 5 to 10°C cooler for the same output, which lowers carbon emissions
  • Available as AL59 ECO and ECO Max conductors

Enquire about HC Alloy

TAL schematic cross-section
TAL
Up to 150°C
Steel coreThermal-resistant alloy

Thermal-Resistant Alloy Conductors (TAL)

Advanced overhead conductors engineered to operate at elevated temperatures up to 150°C while maintaining excellent mechanical strength, conductivity and sag performance. Designed for utilities that need higher power transfer without extensive infrastructure changes, TAL conductors enable efficient uprating of existing networks.

An ideal solution for grid expansion, congestion management, renewable energy integration and capacity enhancement projects that call for higher operating temperatures.

Key advantages

  • Higher operating temperature than conventional conductors
  • More power transmission capacity on existing lines
  • Excellent mechanical strength and reliability
  • Improved thermal performance with controlled sag
  • Less need for tower modifications and right-of-way expansion
  • Enhanced efficiency for grid modernisation
  • Long service life with proven operational reliability

Applications

  • Transmission line uprating
  • Grid modernisation initiatives
  • Renewable energy evacuation networks
  • Congested transmission corridors
  • Urban and metropolitan transmission
  • Utility capacity enhancement
  • High-load transmission
  • Transmission and distribution infrastructure

Construction and material

Specially developed aluminium alloys that keep their mechanical integrity and conductivity at operating temperatures of 150°C. The alloy allows higher current-carrying capacity while minimising thermal degradation, so line capacity can be increased without major infrastructure changes.

Standards and quality

Manufactured in compliance with relevant international standards and utility specifications for electrical, thermal and mechanical performance. Each conductor is manufactured to stringent quality standards, with rigorous testing at every stage, including type testing and validation.

Enquire about TAL

STACIR schematic cross-section
STACIR
Up to 210°C
Aluminium-clad invarThermal-resistant alloy

STACIR and STACIR/TW (INVAR)

STACIR (Super Thermal Resistant Aluminium Alloy Conductor, Aluminium Clad Invar Reinforced) and STACIR/TW are High Temperature Low Sag (HTLS) conductors that significantly increase transmission capacity using existing infrastructure.

An aluminium-clad invar steel (Fe-Ni alloy) core is surrounded by super thermal-resistant aluminium-zirconium (AT3) alloy wires. Operating at up to 210°C, STACIR carries substantially more current than conventional ACSR while keeping lower sag and needing minimal infrastructure changes.

Key advantages

  • Continuous operating temperature up to 210°C
  • Up to 100 to 150% more current-carrying capacity than equivalent ACSR
  • Exceptionally low sag from the aluminium-clad invar core
  • More transmission capacity without building new lines
  • Minimal or no tower reinforcement for uprating projects
  • Excellent thermal and mechanical stability
  • Excellent corrosion resistance and long service life
  • Available in round wire and trapezoidal wire constructions
  • Optimised for congested corridors and urban networks
  • Supports grid modernisation and renewable integration

Applications

  • Transmission line uprating
  • HTLS transmission systems
  • Renewable energy evacuation
  • Grid modernisation programmes
  • Long-span crossings
  • Congested corridors
  • Urban and metropolitan transmission
  • High-capacity networks
  • Substation interconnections
  • Utility and EPC transmission projects

Available variants

  • STACIR (round wire)
  • STACIR/TW (trapezoidal wire)

STACIR/TW uses trapezoidal aluminium alloy strands to maximise aluminium content and improve efficiency and ampacity. Customised sizes and configurations are available on request.

Construction and material

An aluminium-clad invar steel (Fe-Ni alloy) core, with low thermal expansion, surrounded by super thermal-resistant aluminium-zirconium (AT3) alloy wires. The combination gives thermal stability, high conductivity and mechanical strength.

Standards and quality

Manufactured in compliance with relevant international standards and utility specifications. Each conductor is manufactured to stringent quality standards, with rigorous testing at every stage, including type testing and validation.

Enquire about STACIR

ACCC® schematic cross-section
ACCC®
Up to 180°C
Composite coreAluminium 1350

Aluminium Conductor Composite Core (ACCC®)

An advanced HTLS conductor with higher ampacity and significantly lower sag than conventional ACSR. Its lightweight hybrid carbon and glass fibre composite core gives an exceptional strength-to-weight ratio, improved conductivity and better corrosion resistance.

Designed for uprating and grid modernisation, ACCC® conductors let utilities increase power transfer on existing infrastructure. ACCC AZR conductors are also offered for snow-prone areas.

Key advantages

  • HTLS conductor technology
  • Continuous operating temperature up to 180°C
  • Higher current-carrying capacity than conventional ACSR
  • Lowest sag among HTLS technologies
  • Lightweight, with an excellent strength-to-weight ratio
  • Lower electrical losses and better transmission efficiency
  • Better corrosion resistance than steel-core conductors
  • More capacity from existing infrastructure
  • Reduced tower loading from the lighter conductor
  • Long service life with minimal maintenance
  • Grid Vista core allows continuous real-time monitoring of conductor temperature, strain, sag, vibration, ice loading and hot spots

Applications

  • Transmission line uprating
  • HTLS transmission systems
  • Grid modernisation programmes
  • Renewable energy evacuation
  • Long-span crossings
  • Urban and congested corridors
  • Capacity enhancement of existing lines
  • New transmission lines
  • Industrial and utility networks
  • Smart grid and future-ready systems

Available variants

  • ACCC®
  • Info core
  • ULS (Ultra Low Sag) core
  • Grid Vista core
  • ACCC AZR (snow-prone areas)

Available in multiple sizes and configurations. The design can be optimised for ampacity, mechanical loading, span and voltage.

Construction and material

Fully annealed trapezoidal-shaped 1350-O aluminium wires concentrically stranded over a hybrid carbon and glass fibre composite core. The core is very strong with very low thermal expansion, which keeps sag low at high temperature, while the trapezoidal strands maximise aluminium within the conductor diameter for better conductivity and lower losses.

Standards and quality

Manufactured and tested to internationally recognised standards and customer specifications. Each conductor is manufactured to stringent quality standards, with rigorous testing at every stage, including type testing and validation.

Enquire about ACCC®

ACSS schematic cross-section
ACSS
Up to 200°C
Steel coreAluminium 1350

Aluminium Conductor Steel Supported (ACSS)

An HTLS conductor for more transmission capacity, superior thermal performance and reliability. Unlike ACSR, ACSS uses fully annealed aluminium strands supported by a high-strength steel core that carries most or all of the mechanical load.

This allows operation at much higher temperatures with excellent mechanical integrity and controlled sag. ACSS is widely used for uprating, grid modernisation, renewable integration and capacity enhancement without major infrastructure changes.

Key advantages

  • HTLS conductor technology
  • Continuous operating temperature up to 200°C
  • Much higher operating temperature than conventional ACSR
  • More power transfer on existing lines
  • Excellent sag performance at elevated temperatures
  • Steel core carries most of the mechanical load
  • Less need for new corridors and infrastructure
  • Galvanised, aluminium-clad or mischmetal alloy-coated steel cores
  • Corrosion protection options for diverse environments
  • Long service life and low maintenance

Applications

  • Transmission line uprating
  • HTLS transmission systems
  • Grid modernisation programmes
  • Renewable energy evacuation
  • Long-span crossings
  • Urban and congested corridors
  • Sub-transmission and transmission networks
  • Capacity enhancement of existing lines
  • Industrial and utility infrastructure
  • High-capacity projects

Available variants

  • ACSS (round wire)
  • ACSS/TW (trapezoidal wire)
  • Galvanised steel core
  • Aluminium-clad steel core
  • Zn-5% Al-mischmetal coated steel core

ACSS/TW uses shaped trapezoidal strands to maximise aluminium content. Customised configurations are available on request.

Construction and material

One or more layers of fully annealed aluminium 1350-O wires concentrically stranded around a central steel core. The core, in galvanised steel, aluminium-clad steel or Zn-5% Al-mischmetal alloy-coated steel, carries most or all of the load, so the aluminium strands work under reduced mechanical stress.

Standards and quality

Manufactured and tested to internationally recognised standards. Each conductor is manufactured to stringent quality standards, with rigorous testing at every stage, including type testing and validation.

Enquire about ACSS

GAP schematic cross-section
GAP
Up to 210°C
Steel coreGrease-filled gapThermal-resistant alloy

GAP Type Conductor (GTACSR and GZTACSR)

GAP type thermal-resistant aluminium alloy conductor, steel reinforced (GTACSR and GZTACSR) is an HTLS conductor that significantly increases capacity on existing infrastructure.

Thermal-resistant aluminium-zirconium alloy wires (type AT1 or AT3) are stranded over a high-strength steel core with a designed gap between the core and the outer layers. The gap is filled with high-temperature grease so the core and aluminium layers expand independently, giving superior sag performance at everyday and elevated temperatures. Ideal for uprating, valley crossings, renewable integration and grid modernisation.

Key advantages

  • HTLS conductor technology
  • Continuous operating temperature up to 210°C
  • Up to 2x the current-carrying capacity of equivalent ACSR
  • Superior sag performance at elevated temperatures
  • Independent thermal expansion of core and outer layers
  • More capacity without constructing new lines
  • Minimal or no tower reinforcement for uprating
  • Excellent mechanical and electrical performance
  • Corrosion protection from the high-temperature grease system
  • Enhanced self-damping against wind-induced vibration

Applications

  • Transmission line uprating
  • HTLS transmission systems
  • Renewable energy evacuation
  • Grid modernisation programmes
  • Congested corridors
  • Urban transmission infrastructure
  • Long-span crossings
  • Capacity enhancement of existing lines
  • Utility and EPC projects
  • High-capacity networks

Available variants

  • GTACSR
  • GZTACSR (Zn-5% Al-mischmetal coated steel core)
  • Round wire
  • EHS galvanised steel core
  • Aluminium-clad steel (AW) core

Customised conductor sizes and configurations are available on request.

Construction and material

Thermal-resistant Al-Zr alloy wires (AT1 or AT3) concentrically stranded over a high-strength steel core in galvanised, Zn-5% Al-mischmetal coated or aluminium-clad steel. A grease-filled gap between the core and the first aluminium layer lets the two expand independently, minimising thermal sag.

Standards and quality

Manufactured in accordance with internationally recognised standards and utility specifications.

Enquire about GAP

ACS / ACIS schematic cross-section
ACS / ACIS
Aluminium-clad steel

Aluminium Clad Steel (ACS) and Aluminium Clad Invar Steel (ACIS) Stranded Conductor

Stranded conductors that combine aluminium cladding with high-strength steel or low-expansion invar steel cores, for exceptional mechanical strength, better conductivity and thermal performance in transmission and communication infrastructure.

They offer excellent sag performance, corrosion resistance and long-term reliability, and are used in overhead lines, OPGW and advanced conductor systems where both mechanical and electrical performance matter. Available in conductivity from 14% to 40% IACS.

Standards and quality

ASTM B416, EN 61089. ACS conductor data below is to EN 50182.

Aluminium clad steel conductor (ACS), EN 50182
Code nameSectional area
(mm²)
StrandingOverall diameter
(mm)
Weight
(kg/km)
DC resistance at 20°C
(Ω/km)
Rated strength
(kN)
No. of wiresWire dia. (mm)
24-A20SA24.272.106.3161.53.536432.49
34-A20SA34.472.507.5229.02.495346.04
49-A20SA49.573.009.0329.71.732866.30
66-A20SA65.8192.1010.5441.01.310288.18
93-A20SA93.3192.5012.5624.90.9245124.98
117-A20SA117.0192.8014.0783.90.7370156.77
147-A20SA147.1372.2515.8989.20.5881197.13
182-A20SA181.6372.5017.51,221.20.4764243.38
243-A20SA242.5612.2520.31,636.10.3579325.00
299-A20SA299.4612.5022.52,019.80.2899401.24

Enquire about ACS / ACIS

Need a conductor to a utility specification?

Send us the specification or tender reference. We design and manufacture to IS, IEC, EN, ASTM, AS and customer standards.